b16a/b18c sr20det 2jzgte ej205 4g63 srt4 b18a/b18b ka24de 2jzge ej257 4g63 EVO VIII h22/h22a vq35de 1jzgte 4g63 EVO IX k20a/k20z tb48 7mgte k20a3/k24a 2azfe f20c/f22c

The Honda H engine was Honda's high-performance "big block" engine family from the 1990s and early 2000s. It is largely derived from the Honda F engine and shares many design features. It was replaced by the Honda K engine. The primary applications of the H engine series were the fourth- and fifth-generation Honda Prelude, and the fifth- and sixth-generation Honda Accord. It has also enjoyed some success as a racing engine, forming the basis of Honda's Touring car racing engines for many years, and being installed in lightweight chassis (such as the Honda CRX) for use in drag racing. The H22A debuted in 1993 for use in the Honda Prelude VTEC as the H22A1. Versions of the H22A would be the Prelude's signature high-performance engine worldwide until the end of Prelude production in 2001. It was also used in the 1994-1997 Honda Accord SiR and 1998-2002 Honda Accord Euro-R in Japan.

Stage Description Cam # Adv. Dur. Dur @ .050 Lift (in) Lift (mm) Kit # Forced Induction Specification Short duration profile builds cylinder pressure by reducing overlap, high lift for more air intake. Requires kit BC0030 or BC0030S. BC0031 110° 304°/306° 214°/216° 210°/216° 233°/235° 184°/192° 176°/184° .464"/.448" .324"/.312" .262"/.247" 11.78/11.38 8.23/7.92 6.65/6.27 BC0030 or BC0030S Normally Aspirated Specification Hot street/strip or road race specification. Use with CAI, H, E, ECU, A/F mods. Excellent street manners. Requires kit BC0030. BC0032 103° 312°/310° 220°/220° 216°/218° 255°/248° 200°/198° 198°/196° .470"/.469" .325"/.308" .280"/.264" 11.94/11.91 8.25/7.82 7.11/6.70 BC0030 or BC0030S Normally Aspirated Specification Intended for fully built engine. Extensive modifications and tuning capabilities are highly recommended. Requires kit BC0030. BC0033 102° 318°/316° 228°/226° 224°/224° 263°/255° 216°/212° 198°/194° .470"/.470" .360"/.354" .268"/.256" 11.94/11.94 9.14/8.99 6.80/6.50 BC0030 or BC0030S USDM H22A1 (’94-’96) Stock 288°/308° 231°/234° .448"/.415" 11.38/10.54 JDM H22 (’92-’96) Stock 296°/300° 232°/228° .456"/.420" 11.58/10.67 JDM H22A (Type S) Stock 306°/310° 230°/230° .469"/.438" 11.91/11.12 Rocker Ratio: 1.55:1 mid, 1.5:1 sec, 1.45:1 pri.

VALVE SPRING/RETAINER KIT Designed for high rpm, BC valve springs are wound from only the highest grade, super clean, chrome silicone alloy and feature proprietary processing procedures for consistent pressures. BC titanium retainers are CNC machined from 6AL4V round bar titanium to exacting tolerances. Use steel retainer for high mileage applications. Kit # Spring # Retainer # Description BC0030 BC1030 BC2010 Dual spring, titanium retainer BC0030S BC1030 BC2011 Dual spring, steel ret. - high mileage   Spring Pressure: BC1030 Seat: 1.460" @ 88 lbs / Open: 0.950" @ 220 lbs / Coil Bind: 0.790" (no machine work required) Mandatory to check valve guide to retainer clearance prior to operation. STAINLESS STEEL VALVES BC valves are made from premium stainless steel, fully machined and swirl polished for ultimate air flow. Dished head for added weight savings and increased valve control at high rpm. Standard and oversize head. Part # Description # BC3030 35.0mm Intake (standard head diameter) BC3031 30.0mm Exhaust (standard head diameter) BC3034 36.0mm Intake (+1mm head diameter) BC3035 31.0mm Exhaust (+1mm head diameter) HONDA H22/H22A 2.49L STROKER KIT BC 4340 billet steel crankshaft (100mm stroke / 50mm or 55mm main). BC 4340 Econo or Pro Series steel billet rods w/ARP 220,000 psi fasteners. CP aluminum forged pistons (any bore size, any compression ratio). 5100 Series carbon steel alloy wrist pins. 9310 pin upgrade available. Ductile iron plasma top rings, tapered second ring, low tension oil rings. ACL Race Series bearings sold seperately. Fully system balanced and ready to install. (50% deposit required) Kit # Crank # Rod # Piston # Desc. BC0038 BC5039 BC6038 BC7039 55mm main w/BC625+ BC0039 BC5039 BC6039 BC7039 55mm main w/bROD BC0036 BC5039 BC6038 BC7039 50mm main w/BC625+ BC0037 BC5039 BC6039 BC7039 50mm main w/bROD Turn your big block Honda into a 2.49L monster with a BC stroker kit. Big gains in horsepower and torque without sacrificing high rpm potential. Custom CP pistons are made to order so this kit is designed for turbo, supercharger and or nitrous (9:1) as well as all motor (14:1+)...you choose the compression ratio and bore size to suit your specific requirements. Highest quality at an affordable price. Maximum recommended bore size is 89mm. Stock Specifications: H22A 87mm Bore x 90.7mm Stroke - 8.655" Block Height

619.825.8719 ph 619.825.9675 fx Some products listed are not legal for sale or use on emission controlled motor vehicles, RPM ranges vary on application. Warranty Information Copyright © Brian Crower Inc. All rights reserved.